ALL PATCHES FROM A TO Z --- SEE THEM ALL HERE!
HAWAIIAN HIBISCUS & PINEAPPLE - INFUSION SET OVERLAY
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
HAWAIIAN HIBISCUS & PINEAPPLE - LIBRE 2 OVERLAY
Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
HAWAIIAN HIBISCUS & PINEAPPLE - OMNIPOD OVERLAY
Hey Podders! The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the pod and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR PODS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
HAWAIIAN HIBISCUS & PINEAPPLE - DEXCOM G6 OVERLAY
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.65
HAWAIIAN HIBISCUS & PINEAPPLE - LARGE SOLID OVERLAY
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
HAWAIIAN HIBISCUS & PINEAPPLE - LIBRE 3 OVERLAY
Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
HE CAME HE DIED HE AROSE HE ASCENDED HE IS COMING BACK - PATCH
Round Shaped Patch (Solid Patch, Dexcom G6, Omnipod & Libre 2) 3.5 inches x 3.5 inches Smaller Round Shaped Patch (Dexcom G7, Libre 3 & infusion site) 2.75 inches x 2.75 inches The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
HE IS RISEN CROSS PATCH
Oval Shaped 2.75 inch x 3.85 inch - Solid Patch, Dexcom G6 & Libre 2 Smaller Oval Shaped 2.5 inch x 3.5 inch - Dexcom G7, Libre 3 & infusion site Omnipod Shaped 3 inch x 3.85 inch - Omnipod The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.50
HE LEFT THE 99 TO RESCUE ME (MATTHEW 18:10-14) PATCH
Round Shaped Patch (Solid Patch, Dexcom G6 & Libre 2) 3.5 inches x 3.5 inches Omnipod Shaped Patch 3 inches x 3.85 inches Round Shaped Patch (Dexcom G7, Libre 3 & infusion site) 2.75 inches x 2.75 inches The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
HEART CRUSHER VALENTINE PATCH
Custom Medical Grade Hypoallergenic Overlays with Extended Wear Adhesive for CGMs, Pods, and Infusion Sites Sizes and Shapes Round Shaped Patches (Solid Patches/No Cut-Outs, Dexcom G6 & Libre 2) 3.5 inches x 3.5 inches Omnipod Shaped Patches 3 inches x 3.85 inches Smaller Round Shaped Patches (Dexcom G7, Libre 3 & infusion site) 2.75 inches x 2.75 inches Our patches do not contain or include any type of medications or prescription items. They are latex free, and are made solely for the purpose of keeping your pumps and sensors securely attached, while bringing a smile to the not-so-fun stuff that goes with having diabetes.
$2.75
HEDGEHOG LOVE - MEDTRONIC GUARDIAN OVERLAY
Are you looking for overlays that will keep your Deck My Diabetes Medtronic GripShield secure while protecting your Medtronic Guardian sensors? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Medtronic Guardian overlay patches are precut so that the patch fits securely around the Medtronic GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor/transmitter to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS!
$2.50
HEDGEHOG VALENTINE CUTIE PATCH
Custom Medical Grade Hypoallergenic Overlays with Extended Wear Adhesive for CGMs, Pods, and Infusion Sites Sizes and Shapes Round Shaped Patches (Solid Patches/No Cut-Outs, Dexcom G6 & Libre 2) 3.5 inches x 3.5 inches Omnipod Shaped Patches 3 inches x 3.85 inches Smaller Round Shaped Patches (Dexcom G7, Libre 3 & infusion site) 2.75 inches x 2.75 inches Our patches do not contain or include any type of medications or prescription items. They are latex free, and are made solely for the purpose of keeping your pumps and sensors securely attached, while bringing a smile to the not-so-fun stuff that goes with having diabetes.
$2.75
Helmet Head
Round Shaped 3.5 inches x 3.5 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
HEXO ABSTRACT PATTERN - CIRCULAR
Round Shaped 3.5 inches x 3.5 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
HIGHLAND COW SNORKLING PATCH
Custom Medical Grade Hypoallergenic Overlays with Extended Wear Adhesive for CGMs, Pods, and Infusion Sites Sizes and Shapes Round Shaped Patches (Solid Patches/No Cut-Outs, Dexcom G6 & Libre 2) 3.5 inches x 3.5 inches Omnipod Shaped Patches 3 inches x 3.85 inches Smaller Round Shaped Patches (Dexcom G7, Libre 3 & infusion site) 2.75 inches x 2.75 inches Our patches do not contain or include any type of medications or prescription items. They are latex free, and are made solely for the purpose of keeping your pumps and sensors securely attached, while bringing a smile to the not-so-fun stuff that goes with having diabetes.
$2.75
HIPPIE FLOWERS - 8 PATCH SET - LIBRE 3 OVERLAYS
Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
HIPPIE FLOWERS - 8 PATCH SET - DEXCOM G6 OVERLAYS
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
HIPPIE FLOWERS - 8 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAYS
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
HIPPIE FLOWERS - 8 PATCH SET - INFUSION SET OVERLAYS
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
HIPPIE FLOWERS - 8 PATCH SET - LARGE SOLID OVERLAYS
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$18.00
HIPPIE FLOWERS - 8 PATCH SET - LIBRE 2
Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$18.00
HIPPIE FLOWERS - 8 PATCH SET - MEDTRONIC GUARDIAN OVERLAYS
Are you looking for overlays that will keep your Deck My Diabetes Medtronic GripShield secure while protecting your Medtronic Guardian sensors? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Medtronic Guardian overlay patches are precut so that the patch fits securely around the Medtronic GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor/transmitter to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS!
$20.00
HIPPIE FLOWERS - 8 PATCH SET - OMNIPOD OVERLAYS
Hey Podders! The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the pod and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$18.00
HIPPIE VAN CIRCULAR PATCH
Round Shaped 3.5 inches x 3.5 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
HIS MERCIES ARE NEW EVERY MORNING CIRCULAR PATCH
Round Shaped Patch (Solid Patch, Dexcom G6, Omnipod & Libre 2) 3.5 inches x 3.5 inches Smaller Round Shaped Patch (Dexcom G7, Libre 3 & infusion site) 2.75 inches x 2.75 inches The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
HOCKEY
Oval Shaped 3.75 inches x 3.25 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.50
HOLIDAY CHEER - 4 PATCH SET - LARGE SOLID OVERLAYS
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$12.00
HOLIDAY CHEER - 4 PATCH SET - OMNIPOD OVERLAYS
Hey Podders! The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the pod and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$12.00
HOLIDAY CHEER - 4 PATCH SET - DEXCOM G6 OVERLAYS
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$12.00
HOLIDAY CHEER - 4 PATCH SET - LIBRE 3 OVERLAY
Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$12.00
HOLIDAY CHEER - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$12.00
HOLIDAY CHEER - 4 PATCH SET - INFUSION SET OVERLAY
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$12.00
HOLIDAY CHEER - 4 PATCH SET - LIBRE 2
Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$12.00
HOME OF THE BRAVE OBLONG OVAL PATCH
Oblong Oval Shaped 3.75 inches x 3.25 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
HOOEY CIRCLE RED
Round Shaped 3.5 inches x 3.5 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
HOOEY CIRCLE TURQUOIS
Round Shaped 3.5 inches x 3.5 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
Hope For a Cure
Round Shaped 3.75 inches x 3.25 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.50
HORSE ON THE RANGE
Round Shaped 3.5 inches x 3.5 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
Hot Cocoa
3.5 x 3.5 inch Cup shaped adhesive patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$3.00
House Arrest Monitor
For those that ask us the ultimate question! What is that? Is that a House Arrest Monitor? Here's the answer before they ask! Haha! Round Shaped 3.5 inches x 3.5 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$2.75
HOUSE OF CARDS 4 PATCH SET
Oval Shaped 2.75 inches x 3.85 inches Omnipod Shaped 3 inches x 3.85 inches The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$7.50
HUMPTY DUMPTY HAD A GREAT FALL - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
HUMPTY DUMPTY HAD A GREAT FALL - DEXCOM G6 OVERLAY
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
HUMPTY DUMPTY HAD A GREAT FALL - INFUSION SET OVERLAY
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
HUMPTY DUMPTY HAD A GREAT FALL - LIBRE 2 OVERLAY
Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
HUMPTY DUMPTY HAD A GREAT FALL - OMNIPOD OVERLAY
Hey Podders! The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the pod and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR PODS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
HUMPTY DUMPTY HAD A GREAT FALL - LARGE SOLID OVERLAY
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
HUMPTY DUMPTY HAD A GREAT FALL - LIBRE 3 OVERLAY
Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
You have seen 528 out of 1199 products