Welcome to THE SUGAR PATCH!

ALL PATCHES FROM A TO Z --- SEE THEM ALL HERE!

1199 products


  • ROCKETMAN ASTRONAUT  -  DEXCOM G6 OVERLAYS

    ROCKETMAN ASTRONAUT - DEXCOM G6 OVERLAYS

    Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays!  Our variety of overlays are designed with your fashion and lifestyle in mind.  The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

  • ROCKETMAN ASTRONAUT  - DEXCOM G7 OR DEXCOM STELO OVERLAY

    ROCKETMAN ASTRONAUT - DEXCOM G7 OR DEXCOM STELO OVERLAY

    Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $2.50

  • ROCKETMAN ASTRONAUT  - INFUSION SET OVERLAY

    ROCKETMAN ASTRONAUT - INFUSION SET OVERLAY

    Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located.  Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $2.50

  • ROCKETMAN ASTRONAUT  - LIBRE 3 OVERLAY

    ROCKETMAN ASTRONAUT - LIBRE 3 OVERLAY

    Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at  Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $2.50

  • ROCKETMAN ASTRONAUT - LIBRE 2

    ROCKETMAN ASTRONAUT - LIBRE 2

    Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $2.75

  • ROCKETMAN ASTRONAUT - OMNIPOD OVERLAY

    ROCKETMAN ASTRONAUT - OMNIPOD OVERLAY

    Hey Podders!  The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation.  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the pod and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR PODS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $2.75

  • ROCKETSHIPS

    ROCKETSHIPS

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • ROSES TAT PATTERN CIRCULAR PATCH

    ROSES TAT PATTERN CIRCULAR PATCH

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • ROSIE RIVETER - DIABETES AWARENESS

    ROSIE RIVETER - DIABETES AWARENESS

    Round Shaped 3.5 inches x 3.5 inches Adhesive Patch The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.  

  • ROSIE RIVETER - TYPE 1 STRONG

    ROSIE RIVETER - TYPE 1 STRONG

    Round Shaped 3.5 inches x 3.5 inches Adhesive Patch   The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • ROWIN' - ROWIN - ROWIN' ON THE RIVER - KAYAKING - PATCH

    ROWIN' - ROWIN - ROWIN' ON THE RIVER - KAYAKING - PATCH

    Custom Medical Grade Hypoallergenic Overlays with Extended Wear Adhesive for CGMs, Pods, and Infusion Sites Sizes and Shapes Round Shaped Patches (Solid Patches/No Cut-Outs, Dexcom G6 & Libre 2)  3.5 inches x 3.5 inches  Omnipod Shaped Patches 3 inches x 3.85 inches Smaller Round Shaped Patches (Dexcom G7, Libre 3 & infusion site) 2.75 inches x 2.75 inches Our patches do not contain or include any type of medications or prescription items.  They are latex free, and are made solely for the purpose of keeping your pumps and sensors securely attached, while bringing a smile to the not-so-fun stuff that goes with having diabetes.   The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • RUSTY THE LEPRECHAUN GNOME - PATCH

    RUSTY THE LEPRECHAUN GNOME - PATCH

    Custom Medical Grade Hypoallergenic Overlays with Extended Wear Adhesive for CGMs, Pods, and Infusion Sites Sizes and Shapes Round Shaped Patches (Solid Patches/No Cut-Outs, Dexcom G6 & Libre 2)  3.5 inches x 3.5 inches  Omnipod Shaped Patches 3 inches x 3.85 inches Smaller Round Shaped Patches (Dexcom G7, Libre 3 & infusion site) 2.75 inches x 2.75 inches Our patches do not contain or include any type of medications or prescription items.  They are latex free, and are made solely for the purpose of keeping your pumps and sensors securely attached, while bringing a smile to the not-so-fun stuff that goes with having diabetes.  

  • SCHOOL DAYS 4 PATCH SET

    SCHOOL DAYS 4 PATCH SET

    SIZES Dexcom G6, Libre 2 & Solid Patches with no cut-outs = Oval Shaped  2.75 inches x 3.85 inches Dexcom G7, Libre 3 & Infusion Site Patches = Oval Shaped 2.5 inches x 3.5 inches Omnipod Shaped = 3 inches x 3.85 inches The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.  

  • SCHOOL SUPPLIES

    SCHOOL SUPPLIES

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SCIENCE LAB

    SCIENCE LAB

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SEA LIFE FUN CIRCULAR PATCH

    SEA LIFE FUN CIRCULAR PATCH

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SEA TO SHINING SEA CIRCULAR PATCH

    SEA TO SHINING SEA CIRCULAR PATCH

    Round Shaped  3.5 inches x 3.5 inches The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SEAHORSES & SEASHELLS CIRCULAR PATCH

    SEAHORSES & SEASHELLS CIRCULAR PATCH

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SEE YOU LATER EXCAVATOR  - OVERLAY PATCH

    SEE YOU LATER EXCAVATOR - OVERLAY PATCH

    Custom Medical Grade Hypoallergenic Overlays with Extended Wear Adhesive for CGMs, Pods, and Infusion Sites Sizes and Shapes DEXCOM G6 - Circular shaped - 3.5 inches x 3.5 inches  SOLID PATCH/NO CUT-OUT - Circular shaped - 3.5 inches DEXCOM G7 - Circular shaped - 2.75 inches OMNIPOD - Pod shaped - 3 inches x 3.85 inches LIBRE 3 - Circular shaped - 2.75 inches LIBRE 2 - Circular shaped - 3.5 inches INFUSION SITE - Circular shaped - 2.75 inches Our patches do not contain or include any type of medications or prescription items.  They are latex free, and are made solely for the purpose of keeping your pumps and sensors securely attached, while bringing a smile to the not-so-fun stuff that goes with having diabetes. The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

    $2.25 - $2.75

  • SENSOR/INFUSION BARRIERS/UNDERLAY PATCHES FOR DEXCOM G6, MEDTRONIC AND LIBRE 2 SENSORS (NO HOLE)

    SENSOR/INFUSION BARRIERS/UNDERLAY PATCHES FOR DEXCOM G6, MEDTRONIC AND LIBRE 2 SENSORS (NO HOLE)

    UNDERLAY/BARRIER PATCHES 2.35 INCHES X 3.3 INCHES  Great for Dexcom G6, Medtronic Guardian and Libre 2 sensors!  If you are using the Dexcom G7 or Libre 3 sensors, please, use the Dexcom G7/Libre 3 underlay/barrier patches with hole for sensor needle  or Small Generic underlay/barrier patches without hole for sensor needle Many of our friends have experienced severe adhesive reactions from CGM sensors, so we have made some simple unprinted barrier tapes, with the same hypoallergenic tape used in our patches, that will keep the sensor or pump tape from touching the skin and causing reactions, itching, and/or adhesive chemical burns. These Oval Shaped Adhesive Barrier patches go under the sensor, protecting you from the adhesives used in the diabetes technology that you use.  The barriers are large enough to protect your skin under Dexcom G6, Medtronic & Libre 2 sensors, yet small enough to be completely covered by our designer patches/overlays.  We recommend that you also use one of our over patches to additionally secure your sensor, pod or infusion set. APPLICATION INSTRUCTIONS: Barrier/Underlay Patches:  These patches are designed to be applied directly to the skin underneath the sensor, pod, or infusion set to protect sensitive skin from irritation or allergic reactions from their adhesives.  Peel patch away from the backing and apply to clean dry skin where you will be applying the sensor, pod or infusion set.  Apply the sensor, pod, or infusion set over the patch and insert it through the patch.  Apply one of our Overlay Patches over the sensor, pod, or infusion set, to provide extra security.

    $4.25 - $15.50

  • SHAMROCK PATTERN OVAL PATCH

    SHAMROCK PATTERN OVAL PATCH

    Oval Shaped  2.75 inches x 3.85 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • Shark Right at You

    Shark Right at You

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SHINE ON LIGHTHOUSE CIRCULAR PATCH

    SHINE ON LIGHTHOUSE CIRCULAR PATCH

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SHIPS PLANES & AUTOMOBILES OVAL PATCH

    SHIPS PLANES & AUTOMOBILES OVAL PATCH

    Oval Shaped  2.75 inches x 3.85 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SKATERBOARD SMILEY PATCH

    SKATERBOARD SMILEY PATCH

    Round Shaped  3.5 inches x 3.5 inches Omnipod Shaped 3 inches x 3.85 inches   The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • Skull & Crossbones

    Skull & Crossbones

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SMALL GENERIC UNDERLAY / BARRIER PATCHES - SOLID PATCH WITH NO HOLES CUT (FOR DEXCOM G7, STELO, LIBRE 3, LIBRE 2, AND INFUSION SETS)

    SMALL GENERIC UNDERLAY / BARRIER PATCHES - SOLID PATCH WITH NO HOLES CUT (FOR DEXCOM G7, STELO, LIBRE 3, LIBRE 2, AND INFUSION SETS)

    GENERIC UNDERLAY / BARRIER PATCHES - SOLID PATCH WITH NO HOLES CUT - 2 INCHES DIAMETER  ***THIS SIZE WILL WORK WITH INFUSION SETS, DEXCOM G7, STELO, LIBRE 2 OR LIBRE 3 ONLY** Many of our friends have experienced severe adhesive reactions from their INFUSION SETS & SENSORS, so we have made some simple unprinted barrier tapes, with the same hypoallergenic tape used in our patches, that will keep the sensor tape from touching the skin and causing reactions, itching, and/or adhesive chemical burns. The Generic Circular Shaped Adhesive Barrier patches go under the infusion set or sensor, protecting you from the adhesives used in the diabetes technology that you use.  The barriers are large enough to protect your skin under your infusion set and Dexcom G7 or Libre 3 sensors, yet small enough to be completely covered by our designer patches/overlays.  We recommend that you also use one of our over patches to additionally secure your sensor. APPLICATION INSTRUCTIONS: The barrier patches are designed to be applied to the skin underneath the sensor to protect sensitive skin from the adhesive of the sensor. Clean and allow the skin to dry in the area where you will be applying the infusion set.  Gently peel the barrier patch away from the paper backing and apply it to the clean skin where you want your sensor located.  Then apply the sensor or infusion set as you normally would through the barrier patch.  Use one of our overlay patches over your sensor or infusion set and barrier patch to keep it secured to the skin.  Be sure to pat dry the patches, or use a hair dryer on a low setting to dry the patches, after bathing or showering.    

    $10.00 - $25.00

  • SMILEY DAISIES

    SMILEY DAISIES

    Oval Shaped  2.75 inches x 3.85 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SMILEYS - 6 PATCH SET - FOR THE SUGARSHIELD™ CASE BY DECK MY DIABETES for TANDEM MOBI™ INSULIN PUMP

    SMILEYS - 6 PATCH SET - FOR THE SUGARSHIELD™ CASE BY DECK MY DIABETES for TANDEM MOBI™ INSULIN PUMP

    Deck My Diabetes and The Sugar Patch have partnered to create the SugarShield™ case and patches that will allow you to wear your Tandem Mobi™ Insulin Pump securely attached to your body.  The SugarShield™ case, made and sold by Deck My Diabetes, provides easy access with multi-directional placement, for your convenience.  The SugarShield™ case and patches give you the ability to easily change cartridges and infusion sets, shower, and charge your pump.  Visit Deck My Diabetes to order your SugarShield™ case that comes with 2 white SugarShield™ patches. Then, return to The Sugar Patch to get additional designer SugarShield™ patches that are hypoallergenic, comfortable and fun to wear.  

    $18.00

  • SNOWFLAKE MANDALA 3 PATCH SET

    SNOWFLAKE MANDALA 3 PATCH SET

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patches    The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • Soccer Ball

    Soccer Ball

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch    The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • Softball

    Softball

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch    The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SOLID BRIGHT COLORS - 4 PATCH SET  -  LIBRE 2 OVERLAY

    SOLID BRIGHT COLORS - 4 PATCH SET - LIBRE 2 OVERLAY

    Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at  Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $9.00

  • SOLID BRIGHT COLORS - 4 PATCH SET -  INFUSION SET OVERLAY

    SOLID BRIGHT COLORS - 4 PATCH SET - INFUSION SET OVERLAY

    Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located.  Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $9.00

  • SOLID BRIGHT COLORS - 4 PATCH SET -  OMNIPOD OVERLAY

    SOLID BRIGHT COLORS - 4 PATCH SET - OMNIPOD OVERLAY

    Hey Podders!  The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation.  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the pod and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR PODS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $9.00

  • SOLID BRIGHT COLORS - 4 PATCH SET - DEXCOM G6 OVERLAY

    SOLID BRIGHT COLORS - 4 PATCH SET - DEXCOM G6 OVERLAY

    Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays!  Our variety of overlays are designed with your fashion and lifestyle in mind.  The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $9.00

  • SOLID BRIGHT COLORS - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY

    SOLID BRIGHT COLORS - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY

    Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $9.00

  • SOLID BRIGHT COLORS - 4 PATCH SET - LARGE SOLID OVERLAYS

    SOLID BRIGHT COLORS - 4 PATCH SET - LARGE SOLID OVERLAYS

    The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind.    The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin.  We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $9.00

  • SOLID BRIGHT COLORS - 4 PATCH SET - LIBRE 3 OVERLAY

    SOLID BRIGHT COLORS - 4 PATCH SET - LIBRE 3 OVERLAY

    Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at  Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $9.00

  • SOLID COLOR VARIETY - 4 PATCH SET - MEDTRONIC GUARDIAN  OVERLAYS

    SOLID COLOR VARIETY - 4 PATCH SET - MEDTRONIC GUARDIAN OVERLAYS

    Are you looking for overlays that will keep your Deck My Diabetes Medtronic GripShield secure while protecting your Medtronic Guardian sensors?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Medtronic Guardian overlay patches are precut so that the patch fits securely around the Medtronic GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor/transmitter to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS!

    $10.00

  • SOMEWHERE OVER THE RAINBOW PATCH

    SOMEWHERE OVER THE RAINBOW PATCH

    Custom Medical Grade Hypoallergenic Overlays with Extended Wear Adhesive for CGMs, Pods, and Infusion Sites Sizes and Shapes Round Shaped Patches (Solid Patches/No Cut-Outs, Dexcom G6 & Libre 2)  3.5 inches x 3.5 inches  Omnipod Shaped Patches 3 inches x 3.85 inches Smaller Round Shaped Patches (Dexcom G7, Libre 3 & infusion site) 2.75 inches x 2.75 inches Our patches do not contain or include any type of medications or prescription items.  They are latex free, and are made solely for the purpose of keeping your pumps and sensors securely attached, while bringing a smile to the not-so-fun stuff that goes with having diabetes.  

  • SOUTHWESTERN SUN CIRCULAR PATCH

    SOUTHWESTERN SUN CIRCULAR PATCH

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SPACE BIRTHDAY PATTERN PATCH

    SPACE BIRTHDAY PATTERN PATCH

    Custom Medical Grade Hypoallergenic Overlays with Extended Wear Adhesive for CGMs, Pods, and Infusion Sites Sizes and Shapes Large Oval Shaped Patches (Solid Patches/No Cut-Outs, Dexcom G6 & Libre 2)  2.75 inches x 3.85 inches  Omnipod Shaped Patches 3 inches x 3.85 inches Smaller Oval Shaped Patches (Dexcom G7, Libre 3 & infusion site) 2.5 inches x 3.5 inches Our patches do not contain or include any type of medications or prescription items.  They are latex free, and are made solely for the purpose of keeping your pumps and sensors securely attached, while bringing a smile to the not-so-fun stuff that goes with having diabetes. The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SPACE GALAXY

    SPACE GALAXY

    Round Shaped  3.5 inches x 3.5 inches Adhesive Patch  The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.

  • SPARKLING DRAGON - LISA FRANK INSPIRED  -  LIBRE 2 OVERLAY

    SPARKLING DRAGON - LISA FRANK INSPIRED - LIBRE 2 OVERLAY

    Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at  Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $2.75

  • SPARKLING DRAGON - LISA FRANK INSPIRED -  DEXCOM G6 OVERLAY

    SPARKLING DRAGON - LISA FRANK INSPIRED - DEXCOM G6 OVERLAY

    Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays!  Our variety of overlays are designed with your fashion and lifestyle in mind.  The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

  • SPARKLING DRAGON - LISA FRANK INSPIRED -  OMNIPOD OVERLAY

    SPARKLING DRAGON - LISA FRANK INSPIRED - OMNIPOD OVERLAY

    Hey Podders!  The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation.  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the pod and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR PODS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $2.75

  • SPARKLING DRAGON - LISA FRANK INSPIRED - DEXCOM G7 OR DEXCOM STELO OVERLAY

    SPARKLING DRAGON - LISA FRANK INSPIRED - DEXCOM G7 OR DEXCOM STELO OVERLAY

    Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation?  Our variety of overlays are designed with your fashion and lifestyle in mind.   The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at  Deck My Diabetes.  The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch.  There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches.  See our  CLINICAL DATA SUMMARY  for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels.   The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located.  Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer.  To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing.  Center the cut-out (hole) on the patch over the sensor and onto the skin.  Adjustments to the patch can be made before the overlay has been pressed down to the skin.  The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look).  Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it.  After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat.  Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.

    $2.50


You have seen 960 out of 1199 products

ALL PATCHES FROM  A TO Z --- SEE THEM ALL HERE!

Login

Forgot your password?

Don't have an account yet?
Create account