Products
BRIGHT BUTTERFLY - DEXCOM G6 OVERLAY
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
BRIGHT BUTTERFLY - INFUSION SET OVERLAY
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
BRIGHT BUTTERFLY - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
BRIGHT BUTTERFLY - LARGE SOLID OVERLAY
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
BRIGHT BUTTERFLY - LIBRE 3 OVERLAY
Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
BRIGHT BUTTERFLY - OMNIPOD OVERLAY
Hey Podders! The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the pod and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR PODS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
BRIGHT PATTERNS - 4 PATCH SET - LIBRE 2 OVERLAY
Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BRIGHT PATTERNS - 4 PATCH SET - INFUSION SET OVERLAY
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BRIGHT PATTERNS - 4 PATCH SET - OMNIPOD OVERLAY
Hey Podders! The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the pod and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR PODS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BRIGHT PATTERNS - 4 PATCH SET - DEXCOM G6 OVERLAY
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BRIGHT PATTERNS - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BRIGHT PATTERNS - 4 PATCH SET - LARGE SOLID OVERLAYS
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BRIGHT PATTERNS - 4 PATCH SET - LIBRE 3 OVERLAY
Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BUNNY TAILS - 4 PATCH SET - DEXCOM G6 OVERLAY
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BUNNY TAILS - 4 PATCH SET - LIBRE 2 OVERLAY
Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BUNNY TAILS - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BUNNY TAILS - 4 PATCH SET - INFUSION SET OVERLAY
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BUNNY TAILS - 4 PATCH SET - LARGE SOLID OVERLAYS
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BUNNY TAILS - 4 PATCH SET - LIBRE 3 OVERLAY
Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BUNNY TAILS - 4 PATCH SET - OMNIPOD OVERLAY
Hey Podders! The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the pod and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR PODS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BUT FIRST... PUMPKIN SPICE LATTE! - LIBRE 2 OVERLAY
Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
BUT FIRST... PUMPKIN SPICE LATTE! - DEXCOM G6 OVERLAY
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
BUT FIRST... PUMPKIN SPICE LATTE! - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
BUT FIRST... PUMPKIN SPICE LATTE! - INFUSION SET OVERLAY
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
BUT FIRST... PUMPKIN SPICE LATTE! - LARGE SOLID OVERLAY
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
BUT FIRST... PUMPKIN SPICE LATTE! - LIBRE 3 OVERLAY
Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
BUT FIRST... PUMPKIN SPICE LATTE! - OMNIPOD OVERLAY
Hey Podders! The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the pod and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR PODS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
BUTTERFLY ART - 6 PATCH SET - OMNIPOD OVERLAYS
Hey Podders! The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the pod and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$18.00
BUTTERFLY ART - 6 PATCH SET - DEXCOM G6 OVERLAYS
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$18.00
BUTTERFLY ART - 6 PATCH SET - LIBRE 3 OVERLAY
Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
BUTTERFLY ART - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
BUTTERFLY ART - 6 PATCH SET - INFUSION SET OVERLAY
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
BUTTERFLY ART - 6 PATCH SET - LARGE SOLID OVERLAYS
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$18.00
BUTTERFLY ART - 6 PATCH SET - LIBRE 2
Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$18.00
CAMO ASSORTED CIRCULAR 10 PATCH SET
10 assorted camo patches, including one of each of the patches shown. The patches in this set will all be made with the same device option/cut-out. Round Shaped 3.5 inches x 3.5 inches The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$25.00
CAMO ASSORTED OVAL 12 PATCH SET
12 assorted camo patches, including one of each of the patches shown. Oval Shaped 2.75 inches x 3.85 inches The patch designs shown are digital images and the actual patch may have a slightly duller appearance due to the porous material used. Please, refer to your physician or device manufacturer for any questions that you may have regarding the use of tape or patches. **THE SUGAR PATCH LLC is not affiliated with Dexcom, Medtronic, Abbot (makers of Freestyle Libre), Insulet (makers of Omnipod), or any other medical device manufacturer.
$25.00 $22.00
CAMO VARIETY - 12 PATCH SET - LIBRE 2 OVERLAY
Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$23.00
CAMO VARIETY - 12 PATCH SET - INFUSION SET OVERLAY
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$22.00
CAMO VARIETY - 12 PATCH SET - OMNIPOD OVERLAY
Hey Podders! The Sugar Patch designs and makes overlays that will keep your pods secure and looking sweet without causing skin irritation. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Omnipod overlay patches are precut so that the patch fits securely around your pod, and will also work perfectly with the Omnipod GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your pod ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for the duration of your pod. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your pod, use an alcohol swab or non-oily soap and water to clean the skin where your pod will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the pod or patches. Apply your pod by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the pod and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your pod to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and pod site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR PODS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$23.00
CAMO VARIETY - 12 PATCH SET - DEXCOM G6 OVERLAY
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$22.50
CAMO VARIETY - 12 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$22.00
CAMO VARIETY - 12 PATCH SET - LARGE SOLID OVERLAYS
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$23.00
CAMO VARIETY - 12 PATCH SET - LIBRE 3 OVERLAY
Are you looking for overlays that will keep your Libre 3 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 3 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 3 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$22.00
CAMPFIRES & COFFEE - DEXCOM G6 OVERLAY
Don't worry about losing your Dexcom G6 sensors with The Sugar Patch overlays! Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch overlays will keep your sensors secure and looking SWEET! The Sugar Patch Dexcom G6 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G6 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
CAMPFIRES & COFFEE - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
CAMPFIRES & COFFEE - LIBRE 2 OVERLAY
Are you looking for overlays that will keep your Libre 2 sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Libre 2 overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Libre 2 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
CAMPFIRES & COFFEE - INFUSION SET OVERLAY
Are you looking for overlays that will keep your Infusion sets secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Infusion Set overlay patches are precut so that the patch fits securely around your Infusion Site, and will allow you to disconnect and reconnect with ease. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before inserting your infusion set, use an alcohol swab or non-oily soap and water to clean the skin where your set will be located. Be sure that the skin under and around the insertion site is dry, and avoid using lotions, oils or powders near the infusion set or patches. Insert your infusion set by following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
CAMPFIRES & COFFEE - LARGE SOLID OVERLAY
The Sugar Patch LARGE Solid Overlays can be used over low profile sensors such as Medtronic Guardian & LIBRE 2 SENSORS. Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Solid overlay patches fit securely over your sensor, and onto your skin. We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.75
You have seen 144 out of 1036 products