WHAT'S NEW AT THE SUGAR PATCH?!
HALLOWEEN JACK O LANTERN - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
VANILLA CREME - LIGHT SKIN - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
HALLOWEEN LITTLE WITCH - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
PREPPY FANCY FEATHERS - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
EMOJIS - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
CARAMEL LATTE - MEDIUM SKIN - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
COLOR COLLAGE - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
CHASING UNICORNS - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
BUT FIRST... PUMPKIN SPICE LATTE! - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
CAMO VARIETY - 12 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$22.00
ANEEDA AXOLOTL - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
ABSTRACT FLORALS - DEXCOM G7 OR DEXCOM STELO OVERLAYS - 6 PATCH SET
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
STEAMBOAT WILLIE - 3 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$7.50
PREPPY TULIPS & LILIES - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
CAR & TRUCKS - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
CAMPFIRES & COFFEE - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
SOLID BRIGHT COLORS - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
GEOMETRIC BLACK & WHITE - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
HUMPTY DUMPTY HAD A GREAT FALL - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
HALLOWEEN LITTLE GHOST - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
HALLOWEEN NO DIGGITY GHOST DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
HALLOWEEN TOMATO-KIN DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.25
HALLOWEEN TRICK OR TREAT DEXCOM G7 OR DEXCOM STELO OVERLAYS - 6 PATCH SET
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$15.00
HALLOWEEN PATTERNS DEXCOM G7 OR DEXCOM STELO OVERLAY - 6 PATCH SET
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$15.00
COMICAL COFFEE TALK - 8 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
CRUSH TYPE 1 DIABETES MONSTER TRUCK - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
PREPPY TROPICAL FRUIT - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
PREPPY FRIENDS WITH FINS - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
CHRISTIAN PATTERNS - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
ANIMAL HIDE PATTERNS - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
CRAZY LEOPARDS - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
COW PATTERNS - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
CHICKEN CLUCKERS - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
CHARISMATIC KITTIES - 8 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
CATS IN COLOR - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.65
JOY TO THE WORLD SINGING GNOMES - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
BRIGHT PATTERNS - 4 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$9.00
BIRTHDAY PARTY TIME - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
BEACH BALL PATTERN - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
BASEBALL - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
ABSTRACT ART DEXCOM G7 OR DEXCOM STELO OVERLAYS - 8 PATCH SET
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
HALLOWEEN UNICORN WITCH DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.25
TAIL WAGGING DOGGIES - 8 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$17.00
ROCKETMAN ASTRONAUT - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$2.50
PREPPY TROPICAL FLOWERS - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
PREPPY PASTEL PATTERNS - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
PREPPY RAINFOREST - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
COCO MOCHA - DARK SKIN - 6 PATCH SET - DEXCOM G7 OR DEXCOM STELO OVERLAY
Are you looking for overlays that will keep your Dexcom G7 or Stelo sensors secure without causing skin irritation? Our variety of overlays are designed with your fashion and lifestyle in mind. The Sugar Patch Dexcom G7 and Stelo overlay patches are precut so that the patch fits securely around your sensor, and will also work perfectly with the Dexcom G7 GripShield™ from our friends at Deck My Diabetes. The centerpiece that is cut-out of the overlay will be included with your patch, and can be applied to the top of the sensor to complete the design on your patch. There is no reason to pay extra for a sticker to put on your sensor ever again! We use specially formulated medical grade hypoallergenic tape in making all of our overlays and barrier patches. See our CLINICAL DATA SUMMARY for more information on the results of the sensitivity tests performed on our tape. Our tape is designed to last for up to 15 days of wear, depending on your activity level, humidity and temperature levels. The Sugar Patch overlays will last longer when the following application process is followed. Before applying your sensor, use an alcohol swab or non-oily soap and water to clean the skin where your sensor will be located. Be sure that the skin under and around the application site is dry, and avoid using lotions, oils or powders near the sensor or patches. Apply your sensor following the instructions provided by your doctor, or diabetes trainer. To apply the overlay, use the pad of your finger to gently lifte the edge of the patch away from the backing. Center the cut-out (hole) on the patch over the sensor and onto the skin. Adjustments to the patch can be made before the overlay has been pressed down to the skin. The center piece that has been cut-out can be applied to the top of your sensor to complete the patch design (If you are using a GripShield, you may want to do this before applying the overlay and GripShield for a cleaner look). Using a blow dryer on low heat after applying the overlay will help to seal the adhesive to the skin. Avoid getting the patch wet for 4 hours after applying it. After bathing or swimming, be sure to thouroughly dry the patch and sensor site using a clean towel or blow dryer on low heat. Should the edges of the patch ever begin to lift, using a blow dryer on low heat will reactivate the adhesive, and you should be able to press the edges back down to the skin. HAVE FUN AND LIVE LIFE WITHOUT THE WORRIES OF LOSING YOUR SENSORS! ~~ THE SUGAR PATCH LLC is not affiliated with any medical device manufacturers.
$14.00
You have seen 48 out of 62 products